Guide

How to Use a Pool Cover Cable Winch

Updated on · By the Pool Care Pilot team

To use a pool cover cable winch, thread the cable through the cover loops, connect it to the winch, and tighten it evenly to remove slack. Check the cable, grommets, and winch hook before you add tension, then lock the winch and add clips or weights where wind can lift the edge.

On this page (10 sections)
  1. What does a pool cover cable winch actually do?
  2. What should you check before you thread the cable?
  3. How do you thread the cable through the cover loops?
  4. How tight should you make the cable?
  5. How do you lock the winch and check the tension?
  6. When do clips help a cable-secured cover?
  7. When do water tubes work better than clips?
  8. What mistakes make a cable winch hard to use?
  9. How do you care for a cable and winch through the season?
  10. Which setup should you choose for your pool?

To use a pool cover cable winch, thread the cable through every loop on the cover, attach the free end to the winch, and tighten gradually until the slack is gone. Keep the cover centered as you work, and do not pull the cable so tight that it distorts the loops or drags the cover off center.

You will check the parts, thread the cable, set the tension, and decide where clips or weights help. The product picks below show what each helper adds to a cable-secured cover.

What does a pool cover cable winch actually do?

A pool cover cable winch pulls a cable tight around a winter cover so wind has less loose fabric to lift. The cable runs through loops on the cover edge, and the winch removes slack in small steps.

An even pull keeps the cover flat and centered. Loose spots can flap, collect water, and stress the loops.

It works best with swimming pool covers made for cable use. You can also tighten a little, check the shape, then tighten again, which beats tying knots.

What should you check before you thread the cable?

Check the cover loops, the cable length, the winch hook, and the cable channel before you pull anything tight. A short cable or damaged loop will cause problems that more tension cannot fix.

Lay the cover over the pool and walk the perimeter. Look for torn loops, cracked grommets, and places where the edge does not reach the cable line.

Hold the cable to the cover path to confirm it reaches the winch. Inspect the hook and mounting frame for bends or looseness, since a worn part can slip under load.

Our overview of how to string a winter pool cover walks through these checks in order.

How do you thread the cable through the cover loops?

Thread the cable through each loop in order, keeping the cover centered as you go. Start at the winch end so the cable feeds smoothly and does not pile up at the far side.

Work around the pool in one direction. Keep the loose end straight so it does not kink inside a loop.

If the channel is enclosed, feed the cable a short distance at a time. A long push can jam against a seam or fold the cover edge under the cable.

Watch the far side for drift. Pause and recenter the cover before continuing, or a small drift will become a tight spot later.

How do you attach the cable to the winch?

Attach the cable end to the winch hook or fitting and confirm the connection sits fully seated. Leave enough cable between the last loop and the winch so the hook can line up without bending the cable at a sharp angle.

Pull the hook connection by hand to check that it holds. If it shifts, reseat it now, while the cable is still slack.

A hook that looks attached but is not seated will slip when you add tension.

Some winches hold the cable on a drum or spool. If yours does, follow the cover or winch instructions for wrapping and locking the end.

Do not wrap the cable around a part that is not made to hold it.

How tight should you make the cable?

Make the cable tight enough to remove all slack, then stop. The cover should look flat and centered, with no loose pockets or pulled-in distortion at the loops.

Tighten in small turns. After each turn, walk around the pool and check for one side pulling harder than the other.

Watch the loops as you tighten. A loop that stretches, folds, or digs into the cable means stop and check the path.

Stop before the cable bows the cover edge inward.

Our picks for the best pool cover cable winch explain how cable length affects this step. A short cable will force over-tightening at the last loops.

How do you lock the winch and check the tension?

Lock the winch as soon as the slack is gone, then check the whole perimeter before you walk away. An unprotected winch can unwind slowly under wind load.

Most designs use a ratchet, pawl, or locking pin. Engage it fully and try a gentle turn toward loosening to confirm it holds.

Walk the full circle and press lightly on the edge in a few places. No section should lift with a light push.

Check that the cover is still centered. If one side pulled more, ease the tension, recenter, and tighten again in smaller steps.

When do clips help a cable-secured cover?

Clips help where wind can lift the cover between cable loops or at a corner. See above-ground pool cover clips for models that fit above-ground pool rims.

A cable winch holds the perimeter, but clips add grip at points where the cover tries to peel upward.

Above ground pools often rely on clips instead of, or in addition to, a cable. The best pool cover accessories roundup covers the main types, and the right choice depends on your pool wall and rim.

The Beeplove set has 60 clips, each about 4.7 inches long, 1.2 inches wide, and 0.63 inches high. That count lets you space clips closely around a larger rim instead of leaving wide gaps.

Beeplove says the clips suit most permanent above ground pools or pools with metal railings, and not soft sided pools, inflatable pools, or steel frame pools. Check your pool type before you order, since a clip that does not fit the rim will not hold.

Place clips evenly rather than clustering them at one corner. Even spacing spreads the load and keeps the cover from lifting in the middle of a long, unclipped stretch.

What should you know about spring clamps for cover edges?

Spring clamps help at corners and short sections where you need extra grip. They are a flexible add-on, not a full perimeter system.

The EQUIPTZ clamps are 4 inches long with a jaw opening up to 2 inches, and the maker recommends them for items up to 1.5 inches thick. A 20 pound clamping grip is listed for the set of 10.

The jaw pads are wide and non-detachable, which spreads pressure on the cover edge. Soft rubber handles help you open them without slipping, though the spring needs a firm squeeze.

Use several clamps on a large or wind-exposed cover, spaced along the edge. Open them fully before you set them, so the pads sit flat instead of biting at an angle.

When do water tubes work better than clips?

Water tubes work on covers that sit on the pool deck or ground, where weight holds the edge down. They add steady pressure along a stretch of cover instead of point grip.

The Abimars set has 6 tubes, each 8 feet long and 7.5 inches wide. Filled with water, they press the cover down along the perimeter and help block wind from getting underneath.

Abimars says the tubes use 3-layer composite material with E-PVC on the outer layers and a fiber middle layer. A screw cap with a rubber seal closes more securely than a snap cap.

Place the tubes over the cover edge in straight lines. Overlaps at corners help close gaps, and the weight should sit evenly along the full length.

Water tubes suit flat, level ground. On a sloped deck, a tube can creep downhill, so check their position after the first windy night.

What mistakes make a cable winch hard to use?

The most common mistake is tightening the cable before the cover is centered. Once tight, a small offset becomes a large pull at the far loops.

A second mistake is threading out of order or skipping a loop. Wind can work open that weak point and shift load to nearby loops.

A third is ignoring a damaged loop or grommets. Our guide to best pool cover grommets explains how a weak fitting fails under tension.

Replace a worn grommet or reinforce a torn loop before tightening. For Intex pools, fit matters more than tension, as the best pool cover clips for Intex pool guide explains why rim clips and cables do not interchange on every model.

How do you care for a cable and winch through the season?

Care for a cable and winch by checking tension after storms and cleaning the cable before storage. Small checks catch slips and wear while they are easy to fix.

After a storm, walk the perimeter for a shifted cover or slack cable. Re-tighten in small steps and recenter the cover if it drifted.

Wipe down the cable and winch in spring. Dirt in a loop or on a drum can wear the cable and make threading harder next season.

Store the cable coiled loosely and the winch dry. A tight coil can kink the cable, and damp housing can rust parts that hold tension.

See How Does a Pool Cleaner’s Swivel Reduce Cable Twisting? for how a rotating joint prevents twist.

Which setup should you choose for your pool?

Choose a cable and winch if your cover has loops designed for a cable and you want even perimeter tension. Thread the cable in order, tighten in small steps, and lock the winch once slack is gone.

Add clips if wind lifts the cover between loops or at corners. Add water tubes if your cover rests on flat ground and needs steady weight along the edge.

Match the helper to your pool type first, as permanent above ground, in ground, and soft sided pools each grip differently. Start with the best pool cover cable winch picks and confirm cable length against your pool shape.

Frequently asked questions

How tight should a pool cover cable be?

Tight enough to remove slack and keep the cover flat, without pulling the cable so hard that it cuts into the cover or strains the loops. Tighten in small steps, walk around the pool to check the shape, and stop when the cover sits centered and the edge does not sag between anchor points.

Can I use a winch on any winter pool cover?

No. The cover needs a loop or channel designed for a cable, and the cable and winch need to fit that loop size and the pool shape.

Check the cover instructions first, then match the cable length and fitting size to the cover.

If the cover uses clips or water tubes instead, that system may suit it better.

What do I do if the cable keeps slipping?

Stop tightening and check the hook connection, loop condition, and cable path. A worn loop, a bent hook, or a cable crossing at a sharp angle can let the cable slip or cut the cover.

Re-thread the cable through the loops in order, reseat the hook, and tighten again in small steps.

Do I still need clips or water tubes with a cable and winch?

Often, yes, on larger or wind-exposed pools. A cable winch tensions the cover around the perimeter, but clips and water tubes can hold down sections that wind tries to lift.

The right mix depends on the cover type, pool shape, and how exposed your yard is to wind.