How to Replace a Hayward Pool Pump Motor
To replace a Hayward pool pump motor, confirm the frame size, shaft size, voltage, and horsepower on the old motor label first. Then shut off power, drain the pump, remove the seal plate and impeller, fit the new motor with new seals, rewire it, prime the pump, and check for leaks.
On this page (10 sections)
- How do you confirm the right replacement motor for your Hayward pump?
- What tools and parts do you need before you start?
- How do you shut off power and drain the pump safely?
- How do you remove the old motor and seal plate?
- How do you fit the new motor and new seals?
- How do you rewire the new motor and prime the pump?
- How do you test for leaks, noise, and correct rotation?
- When should you replace the whole pump instead of swapping the motor?
- How do you keep the new motor running well?
- Which parts help with related Hayward pump repairs?
To replace a Hayward pool pump motor, confirm the frame size, shaft size, voltage, and horsepower on the old motor label first. Then shut off power, drain the pump, remove the seal plate and impeller, fit the new motor with new seals, rewire it, prime the pump, and check for leaks.
This guide follows that order, and explains when a full pump swap makes more sense. For the general steps, see our pool pump motor replacement guide.
For context on the system, see pool pumps and filters.
How do you confirm the right replacement motor for your Hayward pump?
Match the label, not the guess. Copy the pump model, horsepower, voltage, frame size, and shaft size from the plates on the pump and motor.
Super Pump and Super II models use different frame sizes and shaft heights. A motor that sits too high or low will not line up with the impeller.
Match total horsepower, not just the motor rating. Some Hayward motors list both, and your replacement should match the total the pump was built for.
Check voltage and the wiring box, since a 115 volt motor cannot replace a 230 volt unit without changing the circuit. Photograph the old motor, including the label and shaft end, before removal.
What tools and parts do you need before you start?
Gather new seals, basic hand tools, and a way to catch water. Having everything within reach saves time once the pump is drained.
Put a socket set, adjustable wrench, screwdrivers, pliers, a towel, and a bucket on your list. Add a garden hose for rinsing spills.
Add thread sealant only if your manual calls for it on the connections you will open.
Order new seals with the motor. Opening the seal plate is part of every motor job, so plan on new O-rings and gaskets.
The Carjo Southeastern Accessory Pool Pump O-Ring Seal kit has four rubber pieces for Hayward Super Pump and Super II models, including the SP2610X15 and SP1600M.

Four rubber O-rings and seals for Hayward Super Pump and Super II models, so the seal plate reseals cleanly with the new motor.
See it on AmazonHave a replacement impeller ready if the old one is cracked or worn. A new motor with a damaged impeller will still run poorly.
Keep the old impeller until the new setup works, in case you need to compare part numbers.
How do you shut off power and drain the pump safely?
Turn off the breaker and lock it out before you touch any wiring. Never rely on the pump switch alone while you work on the motor.
Drain the pump housing and filter side as your manual directs. Open the drain plug and lid, and let water flow into a bucket.
Keep the hose nearby to rinse spills away from the electrical area.
Remove the pump lid and basket, and note how the basket sits. Clean the basket now and check the lid O-ring for cracks.
A damaged lid seal can cause air leaks that look like motor problems. Support the pump body so it cannot tip when parts come off, and work on a flat pad where you can set parts in order.
How do you remove the old motor and seal plate?
Remove the seal plate and impeller first, then unbolt the motor. Keep every bolt and washer in order so you can see what goes where.
Take out the seal plate bolts in a cross pattern. Lift the plate straight off to avoid twisting the seal.
Set it face down on a clean towel.
Unscrew the impeller by hand if it turns freely. If it is stuck, hold the shaft with the correct tool and turn with steady pressure.
Do not pry against the seal face, since that can score the surface.
Unbolt the motor feet and slide the motor out. Photograph the wire positions in the junction box before you disconnect anything.
How to replace a Hayward pool pump motor: the removal order
Follow this order to keep the job simple. Seal plate off, impeller off, motor off, then clean and compare.
With the old motor out, clean rust and scale from the feet and seal plate area. Compare the old shaft and frame size with the new motor side by side.
If anything does not match, stop and sort it out before you fit seals.
Check the housing while it is open. Cracks near the strainer or threads can leak even with a new motor.
Our guide to the hayward super pump drain plug covers one common leak point at the base.
How do you fit the new motor and new seals?
Seat new seals in a clean, wet groove, then mount the motor without forcing alignment. Dry fitting parts by hand first shows if the frame sits flat.
Lubricate rubber seals with a thin film of silicone lubricant if your manual allows it. Avoid petroleum products on rubber, since they can swell the material.
Press each seal into its groove with your fingers, not a sharp tool.
Slide the seal plate on and start the bolts by hand. Tighten them evenly in a cross pattern.
Over tightening can warp the plate and cause a leak.
Mount the new motor and check that the shaft lines up with the impeller bore. You should be able to slide the impeller on by hand.
If you must force it, the frame or shaft size is wrong.
What should you check on the strainer housing while the pump is open?
Check the strainer housing for cracks and worn threads before you close the pump. A cracked housing will leak no matter how good the new motor is.
The Cheuyeehui SPX1620AA Pump Strainer Housing Replacement fits Hayward Super Pump SP1600X and SP2600X series models, including the SP1600X5, SP2607X10, and SP2605X7. It uses fiber-reinforced polypropylene and a three-fold sealing ring design, according to Cheuyeehui.

A 2 inch by 2 inch strainer housing for Hayward Super Pump SP1600X and SP2600X models, for when the old housing is cracked.
See it on AmazonMeasure the housing opening and compare the old part number before you order. Doing this now is far simpler than after the pump is running again.
How do you rewire the new motor and prime the pump?
Wire the new motor to match the old wiring, then prime before you start it. Air is the main enemy at this stage, since a dry run can damage the seal.
Connect the ground wire first, then the hot wires as your manual shows. Use terminals rated for the voltage and current, keep the junction box dry, and close the cover before you restore power.
Fill the strainer housing with water until the level holds. Replace the basket and lid, and make sure the lid O-ring sits in its groove.
Turn the motor on for a few seconds, then off. Air often needs two or three short priming runs, so watch the pressure gauge and listen for a rough sound.
How do you test for leaks, noise, and correct rotation?
Run the pump for 15 minutes and check every joint while it runs. Leaks show up fast under pressure, so keep a towel and flashlight handy.
Check the seal plate, lid, drain plug, and both pipe unions. A slow drip at the seal plate usually means a pinched or dry seal, while a drip at a union points to threads or a gasket.
Listen for a smooth hum. Grinding, screeching, or pulsing can mean a worn bearing, a misaligned impeller, or debris in the housing.
Confirm rotation direction matches the arrow on the pump housing. Running backward will move little water, so stop and fix it before running longer.
When should you replace the whole pump instead of swapping the motor?
Replace the whole pump when the housing, impeller, and motor are all worn. A new motor on an old housing can cost nearly as much as a new pump, with less life left.
Salt damage, repeated leaks, and a cracked strainer housing all point to a full swap. If the pump is more than eight years old, ask whether seals, bearings, and the impeller will need work soon anyway.
For a new unit, the Aquastrong Riptide Series 1.5 HP In/Above Ground pump runs at 220 volts with dual speed control. Aquastrong says high speed delivers up to 6,604 GPH and low speed delivers 3,302 GPH, with 1.5 inch and 2 inch adapters included.

A 1.5 HP dual speed 220 volt pump for in-ground and above-ground pools, for when a full pump swap beats a motor-only repair.
See it on AmazonA full swap also lets you move to variable speed. Our guide to the best variable speed pool pump with freeze protection explains what to look for in that upgrade.
How do you keep the new motor running well?
Keep the basket clear, the lid seal clean, and air leaks fixed. Most early failures trace back to debris, dry running, or a small leak left alone.
Empty the pump basket often. Debris that reaches the impeller can score the seal and raise the load on the motor.
A cleaner does not replace the filter, as our post on Why Does an Automatic Cleaner Not Replace the Pool Filter? explains. Wipe down the motor fins so air can cool the housing.
Set a run timer so the pump does not run longer than needed. Our roundup of best intermatic pool pump timer options covers simple mechanical timers for that job.
Which parts help with related Hayward pump repairs?
Keep spares for the parts that fail most often. Seals, a diffuser, and a drain plug cover most repeat repairs.
If flow drops after a motor swap, check the diffuser. Our guide to the hayward super pump diffuser shows how to inspect and replace that part.
For sizing help, our guide to the best hayward 1 hp pool pump motor compares 1 HP options for smaller Hayward pumps. For a broader motor list, see best hayward pool pump motor.
To recap how to replace Hayward pool pump motor units: match the label, fit new seals, wire it right, prime slowly, and test for leaks. If the housing is cracked or the pump is near the end of its life, put that money toward a full pump instead.
Frequently asked questions
How do I know if my Hayward pump needs a new motor or a new seal?
A noisy or humming motor, a shaft that will not turn, or repeated breaker trips point to the motor. Leaks at the seal plate or lid usually point to worn seals.
Check the motor label, inspect the seal area, and compare repair cost before you decide.
Can I replace a Hayward pump motor with a different horsepower?
Only if the pump housing, impeller, and filter system are rated for that output. A larger motor can overload the pump and raise pressure.
Match the original horsepower unless the pump instructions allow a change.
Do I need new seals when I replace the motor?
Yes, fit new seals whenever you open the seal plate. Old gaskets rarely reseat well after removal.
New O-rings and gaskets cost little and prevent leaks that would damage the new motor.
How long does a Hayward pool pump motor replacement take?
Most owners with basic tools can finish in a few hours, including draining, removal, fitting, wiring, and priming. Add time if bolts are corroded, the impeller is stuck, or the electrical box needs attention.
About this guide: Our look at replacing a Hayward pool pump motor draws on maker specs, materials and what owners report. See how we research.


