Guide

How to Replace a Hayward Super Pump Drain Plug

Updated on · By the Pool Care Pilot team

Replace a Hayward Super Pump drain plug by switching off power, closing the valves, removing the old plug, checking the seal, and tightening the replacement by hand. Refill and prime the pump before checking for leaks.

On this page (10 sections)
  1. What do you need before replacing the drain plug?
  2. How do you shut down and isolate the pump?
  3. How do you remove the old Hayward Super Pump drain plug?
  4. How do you check the drain plug seal?
  5. How do you install the replacement drain plug?
  6. What if the pump housing or plug threads are damaged?
  7. How do you refill and prime the pump after the repair?
  8. When should you replace the pump instead of the drain plug?
  9. How do you check the pump after replacing the plug?
  10. What is the safest way to finish the repair?

Replace a Hayward Super Pump drain plug by shutting off power, isolating the pump, checking the O-ring, and tightening the replacement by hand. Refill the strainer pot, restore the valves, and inspect the plug for leaks before running the motor.

A leaking drain plug is often a seal problem rather than a pump-motor problem. Work slowly so you don't damage the plastic threads or leave air in the pump basket.

What do you need before replacing the drain plug?

You need the correct replacement plug, a matching seal, a clean cloth, and access to the pump manual. Have a bucket or towel ready because water may drain from the strainer housing when the plug comes out.

If the pump is part of a larger system, review the basics in pool pumps and filters before isolating it. You should know which valves control the suction and return lines.

Keep the replacement parts clean. Sand, grit, and old seal material can prevent the O-ring from sitting evenly.

How do you shut down and isolate the pump?

Turn off the pump at the electrical disconnect before touching the drain plug. Do not rely only on a timer or a wall switch if the equipment has a separate breaker or disconnect.

Close the valves on the suction and return lines if your system has them. This limits water movement while you remove the plug, but never force a stuck valve.

Open the pump lid slowly if the system may still be under pressure. If water continues to move strongly or the plug area remains pressurized, stop and have the system checked before continuing.

How do you remove the old Hayward Super Pump drain plug?

Remove the drain plug by turning it counterclockwise by hand after the pump is off and isolated. Keep the plug straight as you turn it so the threads do not cross.

Let trapped water drain into a bucket or onto a towel. Water inside the strainer housing is normal, but a strong or unexpected flow means the system may not be fully isolated.

Wipe the plug, threads, and opening clean. Don't scrape the plastic with a sharp tool, and don't force a plug that feels seized.

How do you check the drain plug seal?

Inspect the O-ring for flattening, cuts, cracks, twisting, or embedded grit. A seal that looks dry or distorted should be replaced instead of reused.

The Carjo Southeastern Accessory Pool Pump O-Ring Seal is a rubber, 4-piece kit for Hayward Super Pump and Super II Pump parts. Its listed compatibility includes models such as SP2610X15, SP1600M, SPX1700FG, SP2607X10, SPX1600S, and Super Pump 700.

Use this type of kit when the plug seal is worn and you also need related pump seals for a compatible rebuild. Confirm your exact pump model before ordering, because a broad compatibility list does not guarantee that every part fits every Super Pump.

Clean the sealing groove and the mating surface. If the groove is cracked or the plug threads are damaged, replacing only the O-ring may not stop the leak.

How do you install the replacement drain plug?

Seat the clean O-ring evenly, start the plug straight, and tighten it by hand until snug. The seal should remain in its groove rather than bunching up as the plug turns.

Do not cross-thread the plug. If it becomes difficult to turn after only a few threads, remove it and start again.

Avoid overtightening. Plastic pump parts can crack under excessive force, and a damaged housing may leak even with a new seal.

Don't use thread tape unless the instructions for your exact pump call for it. The seal design determines how the plug closes against the housing.

What if the pump housing or plug threads are damaged?

Replace the damaged part instead of trying to seal a cracked housing with extra tape or sealant. A damaged sealing surface can let air into the suction side or water out of the pump.

The Cheuyeehui SPX1620AA Pump Strainer Housing Replacement is a 2-inch x 2-inch replacement housing for listed Hayward Super Pump SP1600X and SP2600X series models. It weighs 7.83 pounds and measures 5 x 3 x 5 inches.

Cheuyeehui describes the housing as fiber-reinforced polypropylene with a three-fold sealing ring design. Use the model numbers and connection sizes to check fit before replacing a whole housing.

This option suits a repair where the pump body is the problem, not just the drain plug. If the housing is sound and the plug threads are clean, a correctly fitted plug and seal may be all you need.

For a larger internal repair, see how to replace a Hayward Super Pump wet end. If the diffuser is involved, use the steps in how to replace a Hayward Super Pump diffuser.

How do you refill and prime the pump after the repair?

Fill the strainer pot with water before restarting the pump. Replace the lid and confirm that its seal is seated correctly, then reopen the valves gradually.

Check that the drain plug remains snug while the pump is off. If the system has an air-relief procedure, follow the pump and filter instructions before starting circulation.

Turn the pump on and watch the plug, lid, unions, and housing. A few drops during startup call for a shutdown and inspection, not more tightening while the pump is running.

A pump that cannot hold prime may have an air leak at the lid, suction fittings, drain plug, or another seal. Do not run the pump dry.

When should you replace the pump instead of the drain plug?

Replace the drain plug when the plug or seal is the clear fault; consider a pump replacement when the housing, motor, or several major parts are failing. Match voltage, plumbing connections, horsepower, and system needs before choosing a new pump.

The Aquastrong Riptide Series 1.5 HP In/Above Ground is a 220V dual-speed pump. Its high-speed flow is listed as up to 6,604 GPH, while its low-speed flow is listed as 3,302 GPH.

AQUASTRONG lists a pure copper motor, self-priming operation, a filter basket, and 1.5-inch and 2-inch adapters. The pump is described for in-ground and above-ground systems, with dimensions of 14 in L x 12 in W x 30 in H.

This is a system-level choice, not a drain-plug repair. Check your electrical supply and plumbing layout before considering a 220V replacement.

If the motor is the issue, compare the best Hayward 1 HP pool motor options instead of changing the entire pump. A capacitor problem may also be separate from a leaking plug, so see the best pool pump capacitor for that repair path.

How do you check the pump after replacing the plug?

Run the pump briefly and inspect the drain plug for water, air bubbles, and changes in prime. Shut it off before touching any part that leaks.

Look at the plug from several angles. A dry plug with stable circulation is a good sign, but keep checking during the first full operating cycle.

If water leaks from the diffuser or another internal joint, the drain plug may not be the cause. The Hayward Super Pump diffuser gasket guide can help when the gasket area is involved.

A filter problem can also reduce flow without being caused by the pump plug. Review how to change sand in a pool filter if the filter needs service, and read why an automatic cleaner does not replace the pool filter for the difference between cleaning and filtration.

What is the safest way to finish the repair?

A Hayward Super Pump drain plug repair is complete when the plug is straight, the seal is clean and undamaged, the pump holds prime, and no water escapes during operation. Keep the old plug until the repair is confirmed, then store the correct replacement information with the pump manual.

Choose the Carjo kit when a compatible Hayward pump needs a replacement rubber seal or several related O-rings. Choose the Cheuyeehui housing only when the compatible strainer housing itself is damaged.

Consider the Aquastrong pump when the repair has grown into a full pump replacement and your system supports 220V.

Hayward's official pool pump support resources should take priority for model-specific procedures and replacement-part checks.

If the plug still leaks after a new seal and careful hand tightening, stop running the pump and inspect the threads and housing for damage. A small drain-plug repair should not become a cracked-housing or dry-run problem.

Frequently asked questions

How do you replace a Hayward Super Pump drain plug?

Turn off power, close the pool valves, open the lid carefully, and remove the old drain plug by hand. Inspect the O-ring and threads, fit the correct replacement, tighten it by hand, reopen the valves, refill the strainer pot, and check for leaks before restarting the pump.

Should you use tape on a Hayward Super Pump drain plug?

Don't add thread tape unless the pump manual specifically calls for it. A drain plug that seals with an O-ring needs a clean sealing surface and an undamaged seal; extra tape can make the plug fit poorly or hide a damaged O-ring.

Why does a Hayward Super Pump drain plug leak?

A Hayward Super Pump drain plug can leak when its O-ring is worn, twisted, dirty, dry, or damaged. Cracked threads, cross-threading, a loose plug, or a damaged pump housing can also cause seepage, so inspect both the plug and the sealing area.

How tight should a Hayward Super Pump drain plug be?

Tighten the Hayward Super Pump drain plug by hand until it is snug, following the pump manual for any model-specific instruction. Do not use pliers or a wrench unless Hayward directs you to, because excess force can damage the plug, O-ring, or housing.